文档帮助中心文档
使用半导体和转换器转换和纠正功率。
全部ows the user to explore the impact of parameter choices on the I-V and C-V characteristics for a surface-potential-based MOSFET model. To open this example, in the MATLAB® Command Window, type: ee_mosfet_characteristics.
控制目标转换器的输出电压。为了调整占空比,控制子系统使用基于PI的控制算法。在整个仿真过程中,输入电压被认为是恒定的。可变电阻为系统提供负载。总仿真时间(T)为0.25秒。在t = 0.15秒时,负载变化。
控制一个四季度斩波器。控制子系统实现了一种简单的基于PI的控制算法,用于控制输出电流。模拟使用正面和负面参考。总仿真时间(T)为1秒。在t = 0.5秒时,负载直流源E的极性更改。
这是分析工作流程示例的基本模型。
将30V直流电源转换为受监管的15V直流电源的A交换电源。该模型可用于尺寸尺寸的电感L和平滑电容器C,以及设计反馈控制器。通过在连续和离散控制器之间选择,可以探索离散化的影响。
具有基本负载,酒店负载,弓推进器和电动推进的代表海洋半舰电力系统。
在电源转换器中使用不同级别的保真度。该系统包含三个转换器。顶部转换器在10 US样品时间使用理想的开关和保护二极管。为了产生准确的结果,即使模型在50个美国样本时间进行采样,中间转换器使用平均脉冲的平均开关。为了进一步提高样品速率并作为理想平均转换器运行,底部转换器使用平均开关和调制波形而不是门脉冲。控制子系统包含一个三相,两级PWM波形生成器。范围子系统包含范围块,使您可以看到模拟结果。
一个三相矩阵转换器,可驱动静态负载并在源上绘制统一功率因数。范围子系统包含范围,使您可以查看模拟结果。
How a varistor may be applied to a buck converter in order to protect the switching MOSFETs from over-voltages due to a differential surge.
控制反转拓扑降压转换器的输出电压。反转拓扑降压转换器仅使用一个开关,而输出电压的极性与输入相反。为了调整占空比,控制子系统使用基于PI的控制算法。在整个仿真过程中,输入电压和系统负载被认为是恒定的。总仿真时间(T)为0.25秒。在t = 0.15秒时,电压参考变化,系统从摇滚模式转换为增强模式。
正确使用PFC pre-converter功率因数。This technique is useful when non-linear impedances, such as Switch Mode Power Supplies, are connected to an AC grid. As the current flowing through the inductor is never zero during the switching cycle, the boost converter operates in Continuous Conduction Mode (CCM). The inductor current and the output voltage profiles are controlled using simple integral control. During start up, the reference output voltage is ramped up to the desired voltage.
You clicked a link that corresponds to this MATLAB command:
Run the command by entering it in the MATLAB Command Window. Web browsers do not support MATLAB commands.
选择一个网站以获取可用的翻译内容,并查看本地事件和优惠。根据您的位置,我们建议您选择:。
您还可以从以下列表中选择一个网站:
选择中国网站(中文或英语)以获得最佳场地性能。其他Mathworks乡村网站未针对您所在的访问进行优化。
联系您当地的办公室