Add PWM Driver Block

Step 4 of 7 in Add Hardware Drivers to Simulation Model and Deploy to Target Hardware

In the Simulink^®Library Browser, add the ePWM block fromEmbedded Coder^®Support Package for Texas Instruments™ C2000™ Processors> F2837xD.

Configure the ePWM1, ePWM2, and ePWM3 blocks for generating the PWM pulse. In the ePWM block parameters dialog box, calculate the pulse width modulation (PWM) counter period register value from the CPU frequency and the PWM frequency. For center-aligned PWM, divide the value by2.

PWM counter period = CPU clock frequency / PWM frequency /2

See the TMS320f28379d processor ePWM peripheral for more details.

在F2837x / 07x/004x/38x ePWM block parameters dialog box, update the settings to configure PWM1 to generate PWM pulses in the target hardware as shown in this table.

Tab and Parameter in ePWM Block	Settings
General>Module	ePWM1
General>Timer Period	Enter the PWM period value in the CPU clock cycle PWM counter period = CPU clock frequency / PWM frequency /`2` For LaunchPad 28379D, clock frequency is`200`MHz. For PWM frequency of`20`kHz, PWM counter period =`200e6 / 20e3 / 2`; PWM counter period =`5000`
Counter Compare>Specify CMPA via	Input port
Counter Compare>CMPA initial value	Enter the PWM counter period/`2`(`2500`)
Counter Compare>Specify CMPB via	Input port
Counter Compare>CMPB initial value	Enter the PWM counter period/`2`(`2500`)
Deadband unit>Use deadband for ePWM1A	`on`
Deadband unit>Use deadband for ePWM1B	`on`
Deadband unit>Deadband polarity	Active high complementary (AHC)
Deadband unit>Deadband Rising edge (RED) period (0~16383)	`15`
Deadband unit>Deadband Falling edge (FED) period (0~16383)	`15`
Event Trigger>Enable ADC start of conversion for module Acheck box (only for PWM1)	`on`
Event Trigger>Start of conversion for module A event selection(only for PWM1)	Counter equals to period (CTR=PRD)

Rename the block as ePWM1.

在F2837x / 07x/004x/38x ePWM block paramters dialog box, update the settings to configure PWM2 and PWM3 to generate PWM pulses in the target hardware. PWM2 and PWM3 are synchronized with PWM1. Follow ePWM1 configurations (other than Event Trigger) and add the configurations as shown in this table.

Tab and Parameter in ePWM Block	Settings
General>Module	ePWM2
General>Timer Period	Enter the PWM period value in the CPU clock cycle PWM counter period = CPU clock frequency / PWM frequency /`2` For LaunchPad 28379D, clock frequency is`200`MHz. For PWM frequency of`20`kHz, PWM counter period =`200e6 / 20e3 / 2`; PWM counter period =`5000`
General>Synchronization action	Set counter to phase value specified via dialog
General>Counting direction after phase synchronization	Count up after sync
General>Phase offset value (TBPHS)	`0`
Counter Compare>Specify CMPA via	Input port
Counter Compare>CMPA initial value	Enter the PWM counter period/`2`(`2500`)
Counter Compare>Specify CMPB via	Input port
Counter Compare>CMPB initial value	Enter the PWM counter period/`2`(`2500`)
Deadband unit>Use deadband for ePWM1A	`on`
Deadband unit>Use deadband for ePWM1B	`on`
Deadband unit>Deadband polarity	Active high complementary (AHC)
Deadband unit>Deadband Rising edge (RED) period (0~16383)	`15`
Deadband unit>Deadband Falling edge (FED) period (0~16383)	`15`

Rename the blocks as ePWM2 and ePWM3.

Select CMPA and CMPB as input ports where PWM duty is given as input. The range varies from0toPWM_counter_period. PWM outputs when PWM up-counter matches CMPA and PWM down-counter matches CMPB. By default, the system inputs a duty cycle of 50% by selecting PWM counter period /2.

Enable dead time in the ePWM configuration. On the Event Trigger tab of PWM1 module, select ADC start of conversion event when the PWM counter equals the PWM period. In the SOC Trigger tab of the ADC block, selectSOCx触发源asePWM1_ADCSOCA.

Synchronize the ePWM2 and ePWM3 blocks with the ePWM1 block by setting the synchronization timing to the moment when the PWM counter equals to zero in the ePWM2 and ePWM3 blocks.

The ePWM blocks expect the duty cycle value to range from0to period counter register (5000). Control_System subsystem outputs the PWM in the range-1to1. This model scales the output to0to5000(period counter value).

For simulation, add a variant source/sink to the hardware driver block for simulation and code generation.

Add Hardware Drivers to Simulation Model and Deploy to Target Hardware

金宝app

Introduction to Brushless DC Motor Control

Get ebook