使用复杂信号验证IP2/IP3
此示例显示了如何使用RF BloveSet™电路包膜库来运行两色调实验,该实验测量放大器的二阶和三阶截距点。该模型从每个载波上测量的调制信号功率计算放大器的截距点,从而验证RF模块化系统的行为。使用RF预算分析仪应用程序和测量测试台确认这些值。
System Architecture
该系统由:
Two complex voltage sources connected in series. The first voltage source is modeled with Simulink® blocks, and the second with blocks from the RF Blockset circuit envelope library. In the Simulink Source subsystem, two series Sine Wave blocks model in-phase and quadrature components of the first tone. An Inport block assigns the Simulink signal to the carrier
FC1
。在RF模块源子系统中,两个系列正弦波模型内相和正交电压信号调节载波FC2
。A resistor modeling the voltage source impedance.
An amplifier with input impedance, output impedance specified in the Main tab; output IP2, and output IP3 specified in the Nonlinearity tab.
An Outport block that probes the output voltage of the amplifier across a shunt Resistor block. The ordering of the output signals is determined by the ordering of the carriers specified in the Outport block dialog.
一个子系统,以计算输入,IP2和IP3频率以运行RMS功率级别。
A subsystem to compute IP2 and IP3 intercept points [1].
示例模型使用回调函数定义了块参数的变量。要访问模型回调,请选择MODELING>模型设置>模型属性一种nd click the Callbacks tab in the Model Properties window.
运行示例
Type
open_system('simrfv2_carriers')
在命令窗口提示符处。选择Simulation>跑。
输出功率和放大器输出截距点显示在模型的右侧。计算功率子系统使用运行的根平方(RMS)平均值计算每个交流产品的DBM功率。
建模非线性RF阻滞组件
在RF模块电路信封环境中建模非线性:
将放大器或搅拌机块放入模型中。
指定生成非线性的参数,例如IP2一种ndIP3,注意在“块”对话框的“非线性”选项卡中直接指定公约或指定多项式。
指定在配置块中模拟的任何其他载波频率。在此示例中,配置块指定了总共25个频率:
FC1
一种ndFC2
,作为基本音调输入信号;一种谐波顺序每种音调的3中,产生了一组完整的第二,第三阶,四阶交换产物(包括二阶和三阶谐波产品),以及一组五阶和六阶间隔产品。下载188bet金宝搏
为了计算每个包膜的功率水平,测得的电压信号以特征阻抗的平方根倒数缩放。额外的缩放1/sqrt(2)
in the Calculate Power subsystem normalizes the complex-valued output signal.
使用测量台验证
相同的测量可以执行使用RF Budget Analyzer app to automatically generate the model and testbench.
打开RF预算分析仪应用程序并指定放大器。
定义其IP3(目前无法指定IP2)。
Generate the measurement testbench.
打开测试的设备以揭示放大器。指定IP2值。
禁用噪声以对IP2和IP3进行准确的测量。(使用RF测量单元对话框)。
运行模拟并测量IP3。
Change the quantity to be verified to IP2 and rerun the simulation.
如果您在测试台的面罩下查看,则可以找到用于测量IP2和IP3的逻辑。该方法与初始模型中描述的非常相似。
Reference
肯德特,肯。“ IP2和IP3的准确和快速测量。”The Designers Guide Community, Version 1b, May 22, 2002.