变压器磁滞设计工具
可饱和变压器块的可饱和核心的查看和编辑磁滞特征
Description
这磁滞设计师app allows you to view and edit a hysteresis characteristic for the saturable core of the多方面变压器,,,,Saturable Transformer,,,,三相变压器(两个绕组),,,,andThree-Phase Transformer (Three Windings)块。磁滞特征包括位于磁滞回路极限的饱和区域。
A default hysteresis characteristic displays when you open the app, but you can build as many hysteresis characteristics as you want and save them in different MAT-files. You can use the same characteristic for all your transformer blocks, or you can use different characteristics for each transformer block in the circuit. In the mask of a transformer block, selectSimulate hysteresisand specify a MAT-file to use.
这磁滞设计师app includes a flux animation tool that can visualize how bySIMSCAPE™Electrical™专门的电力系统软件执行磁滞的模拟。这是模型参数化不需要的可选工具。该应用根据定义的滞后特征计算初始轨迹。该工具假设启动通量之前的最后一个反转点位于主要循环上。操作点会传播,直到定义的停止通量为止。
打开变压器磁滞设计工具应用程序
MATLAB®command prompt: Enter
power_hymsteresis
In thePowergui块,单击磁滞设计师
参数
滞后参数参数单元
- 应用程序参数单元
pu
(默认)|si
转换定义滞后特性的通量和电流si
至pu
or frompu
至si
。
细分市场
- 线性段的数量
512
(默认)|32
|64
|128
|256
用于定义滞后环的右侧的线性段数量。环的左侧是右侧的对称图像。
Remnant flux FR
— Remnant flux
0.85 (default) | positive scalar
Remnant flux point of the hysteresis characteristic (flux at zero current). The remnant flux point is identified by a + mark in the plot.
强制电流IC
— Coercive current
0.004 (default) | positive scalar
Coercive current point of the hysteresis characteristic.
dF/dI at coercive current
— Flux slope at coercive current
1000(默认)|正标量
Slope of the flux at the coercive current point (current at zero flux).
Saturation flux Fs
- 饱和通量
1.2 (default) | positive scalar
饱和磁滞回路成为单值饱和曲线的饱和通量点。饱和通量点通过图中的一个 *标记识别。
Saturation current Is
— Saturation current
0.015 (default) | positive scalar
滞后循环成为单值饱和曲线的饱和电流点。饱和区域由饱和区域电流范围。
名义参数[P(VA),V(VRMS),F(Hz)]
— Transformer nominal parameters
[150E6,500E3/sqrt(3),60](默认)|向量3
Nominal parameters (nominal power in VA, nominal voltage of winding 1 in volts RMS, and nominal frequency in Hz) used in the conversion of the hysteresis parameters.
饱和区域电流
— Saturation current
[0.015 0.03 0.06 0.09 0.12 2.5e+12](默认)|向量
定义饱和特性的电流值的向量。指定点的数量必须与饱和区域通量范围。您只需要指定特征的积极部分。
饱和区域通量
— Saturation current
[1.2 1.35 1.5 1.56 1.572 1E+12](默认)|正标量
定义饱和特性的磁通值的向量。指定点的数量必须与饱和区域电流范围。您只需要指定特征的积极部分。
Tolerances [Tol_F, Tol_I]
— Saturation current
0.015 (default) | positive scalar
该参数主要用于最大程度地减少多余的,非常小的内部环或新轨迹的生成,因为它们的效果很小,并且消耗了计算机存储空间。该模型可以随时记住多达50个嵌入式小环。
这tol_f参数是用于检测wh公差值ether, after a flux reversal, the operating point remains on the same minor loop or a new embedded loop is created. The smaller the value, the lesser the effect on the normal trajectory behavior. The bigger the value, the lesser the generated number of embedded minor loops.
Finally, when the distance between the I coordinate of the actual point of reversal and the penultimate one is less thantol_i,然后在这两个点内的演变遵循线段而不是循环。
放大滞后
— Saturation current
在(默认)|离开
选择要放大滞后曲线周围的图。
开始
— Starting flux
0.0(默认)|标量
起动磁通。
停止
- 结束助焊剂
? (default) | scalar
Flux at which the flux animation stops.
三角洲
- 助焊剂三角洲
1,78E-08(默认)|正标量
Flux increment, in pu or SI, that is used to go from start flux to stop flux.
Update diagram
- 更新磁滞图
Update the hysteresis diagram after you changed hysteresis parameters.
动画
— Animate flux animation
启动Flux动画工具。
Reset
- 重置磁通动画
重置Flux动画工具。
加载
- 负载磁滞参数
打开一个浏览器窗口,您可以在其中选择自己的电缆数据。选择所需的垫子文件。
Save
- 保存滞后参数
Saves your cable data by generating a MAT-file that contains the GUI information and the cable data.
Help
- 应用程序文档
Open the documentation page of the app.